Outdoor Waterproof Wall Panel Metal House Siding
Metal wall thermal insulation decorative board, metal embossed fireproof and heat insulation integrated board, referred to as metal carved board, is formed by rolling the metal embossed board on the surface, after heating, filling with hard thermal insulation foam material as the core layer, and then It is processed by pasting aluminum foil paper on the back.
Products Description
Metal carving panels, outdoor waterproof wall panel metal house siding are new wall environmental protection materials developed in recent years. The outer layer is mainly made of galvanized color steel plates. Rolled into different styles of patterns, or painted into a variety of colors after secondary coating, forming such as: antique brick pattern, bullet-painted pattern, corrugated pattern, wooden double eyelid pattern, marble pattern, fine stone pattern, etc. Various patterns can meet the appearance requirements of architectural shapes and colors, and achieve a certain artistic effect.
The thermal insulation material in the middle of the board is usually polyurethane foam (PU, PIR), and its interior is an independent closed cell structure. The aluminum foil pasted on the back can effectively reflect the heat source and play the role of heat insulation, heat preservation and moisture resistance. The combination of concave-convex plug-in and groove type makes the construction very simple. Metal carved galvanized composite insulation board is a kind of excellent performance building material with high compression resistance, moisture resistance, low thermal conductivity, beautiful appearance, durability, energy saving, convenient construction and environmental protection.
Products installation
Heat preservation treatment of wall panel sentry box
Unlike our living buildings, the metal carved board sentry box has good thermal insulation. Its materials are relatively thin during construction, so it will be relatively cold in winter, so how should it take some heat preservation measures?
1. The first thing is to check whether there are any loopholes and fill in the gaps
Check the sentry box in use, and use tape or other materials to block the small gaps that are easy to enter the wind. In the sentry box with metal carved panels, add a layer of heat-insulating material, and if conditions permit, you can also add some warm waste cloth, etc., or lay a layer of carpet, but the fire prevention measures for the sentry box should be taken well.
2. The heating method used
It is a relatively simple and direct method to increase the internal temperature of the stainless steel security sentry box through air conditioning or electric heating. Combined with the first two small methods, you can spend the winter in the sentry box warmly.
3. Add materials
The wall of the metal carving board sentry box is different from the wall of our home life, and the outer wall of the sentry box is very cold, especially in winter. Therefore, before winter comes, it is necessary to add a layer of thermal insulation material to the outside of the security box. In order to make the temperature of the security sentry box reach a more suitable temperature for the human body, thermal insulation materials should be used at the entrance of the sentry box to make it thicker.
4. Indirect method:
The addition of materials fundamentally improves the temperature of the metal carved board sentry box. The indirect method is mainly for temperature control inside the metal carved board sentry box, if we do not install air conditioners or other heating equipment. A few warm rugs can be laid on the ground of the sentry box, and some thick cardboard can be pasted on the inner wall of the sentry box to increase its temperature.
Although the metal carved board itself has certain thermal insulation properties, it is limited after all. It can play a very good role in living buildings, but for sentry boxes, the thermal insulation properties will still be worse, so some other measures need to be taken. measure.
Packing & Delivery
Selling Units: Single item
Single package size: 44X18X7 cm
Single gross weight: 0.700 kg
Package Type: Composite Facade Light Weight Decoration External Pu Sandwich Panel:
Package Material: Carton.
Standard Package Size: 3840*420*150 mm.
Package Quantity: 9 pieces/pack. *
Gross Weight: 46.5 kg/pack.
Customerised package: Available.
Product news
How To Do Exterior Wall Waterproofing Planning？:
Exterior wall decorative foam panels can not only play a role in heat preservation and energy saving but also beautify and decorate so that decorative insulated wall panels can serve us for a long time, so we should take some waterproof measures for external wall insulation materials. Next, we will pick some waterproof design methods, I hope we can help you.
1. Asphalt waterproofing membrane during use: use base paper, fibers, and fabrics to coat asphalt. It can be made into professional waterproof construction materials.
2. One waterproof maintenance: professional waterproof equipment.
3. Asphalt for waterproofing construction roll: base paper, fiber, fabric, fiber felt, and other carcass materials are used to dip-coat asphalt, and the surface is sprinkled with powdery, granular, or sheet-like structural materials to make bendable sheet-like or waterproof engineering materials.
4. Polymer-modified asphalt waterproofing membrane: The synthetic polymer-modified asphalt is used as the coating, the fiber fabric or fiber mat is used as the substrate, and the sheet or film material is used as the coating material to make a flexible sheet waterproof material.
5. Composition research Polymer waterproof membrane: it is made of synthetic rubber, synthetic resin, or their blend through the two as the base material, adding the appropriate amount of chemical additives and fillers, etc., and processed through different production processes. Flexible sheet-like waterproof engineering materials, or composite development of the above-mentioned analytical materials and synthetic fibers to form flexible sheet-like waterproof building materials with two or more layers.
6. Floor glue is cold asphalt cement made of petroleum asphalt, fillers, solvents, etc.
7. Bottom surface treatment agent: To enhance the adhesion, the paint on the bottom layer is pre-painted before the construction of the waterproof layer.
8. Slits: To reduce cracks, pre-set seams on the roof leveling layer, rigid waterproof layer, and rigid maintenance layer. The rigid protection layer is made into a V-shaped groove on the surface, which is called a surface for divisions.
9. Full sticking method (full sticking method): When laying waterproof materials, the construction method of full sticking between the coiled material and the bottom layer is adopted.
10. Empty laying method: When laying waterproof membranes, the membranes and the bottom layer are only bonded for a certain period around the surroundings, and the other two parts are not bonded.
11. Strip bonding method: When laying waterproof membranes, the construction method of strip bonding is used for the membrane and the bottom layer. There are no less than two bonding surfaces between each coil and the bottom layer, and the width of each data is generally not less than 150mm.
12. Dot sticking method: When laying a waterproof membrane, the membrane or perforated membrane should be dotted on the bottom layer. The bonding area between each square meter is not less than 5 points, and the area of each point is 100mm×100mm.
13. Hot-melt method: The traditional flame heater can be used to melt the hot-melt waterproof membrane as the bottom hot-sol for an effective bonding construction management method.
FAQ
Q: How to install your product?
A: Easy. Screw the outdoor waterproof wall panel metal house siding onto steel/wooden frame, then apply the accessories to the corner/connecting
areas. Done.
Q: Can I get free sample?
A: Sure. We supply free samples, you only need to pay the courier fee.
Q: Do you accept small orders?
A: Yes. If you are a builder, or small retailer or starting up business, we are definitely willing to grow up with you. And we are
looking forward to co-work with you for a long term relationship.
Q: Can you make the price cheaper?
A: We always take our customer's benefit as the top priority. Price is negotiable under different conditions, and we are assuring
you to get the most competitive price.
Q: What's your MOQ:
A: Stock products: 1 m². Producing products: from 100 m².
Q: How long is your delivery time?
A: Standard products: 1~5 days. Customized products: 10-30 days.
We have 4 advanced production lines with daily capacity of 18,000 m², and thousand tons of raw materials in stock, to guarantee
100% on time delivery.
Q: How do you guarantee the quality?
A: Each product has strict testing procedures (from raw material selecting, manufacturing, quality checking, packing, and loading,
etc.), and must be 100% quality checked before delivery.
Q: Can you do OEM?
A: Yes, we not only do OEM, but also do ODM. We can customize your logo onto product package.
Q:What else can you provide?
A:We not only provide decorative outdoor wall panel, also offer various of exterior and interior products.
Besides, we are willing to support you with sourcing any other products which you may looking for.
Hot Tags: outdoor waterproof wall panel metal house siding, China outdoor waterproof wall panel metal house siding manufactures, suppliers, factory, corrugated steel wainscoting, cladding metal panels, steel panels for exterior walls, frp wall, metal faced insulation panels, plastic paneling
