Exterior Wall Siding Sandwich Panel

Exterior Wall Siding Sandwich Panel

Product introduction

Metal carved panel is a kind of exterior wall insulation decorative one piece board, is also composed of finish layer and insulation layer. The reason it is called metal sculpture panel is mainly because the finish layer uses metal paint; and the metal paint used in metal sculpture panel is mainly fluorocarbon metal paint that is added to metal powder in fluorocarbon paint. Metal insulation panel has excellent thermal insulation characteristics, compared with the traditional exterior wall insulation decorative building materials, has excellent cold insulation performance. It reduces heating and cooling energy consumption to a great extent, thus saving energy expenditure. The products are cost-effective and show absolute advantages in exterior wall insulation and decoration material products.

 

 

Product specification

In recent years,what we all know is that exterior metal faced sandwich panel 16mm is often used in the construction industry because the product is very convenient to use, Now,let's understand the specific parameters of the product.

1, Metal carved board surface material: 0.3mm aluminum steel plate + polyester 2 layer film +3 ~ 7 layers of paint

2, Core material: hard foam polyurethane

3, Inside material: aluminum film cover + waterproof lining paper

4, Thermal conductivity: 0.089 W (M-K) (average temperature 28.56 ℃), GB/T10294-1999

5, Acid resistance: 2%HCI solution 48h, no change in the sample surface, GB/T17748-1999

6, The volume: the weight of the test piece volume is 24 decibels, GBJ175-1999

7, Heat flow resistance rate: Mhc/ KCAL, 0.79

8, Metal carved plate heat flow rate: Kcal/ MHC, 1.27

9, Heat conductivity: Kcal/ MHC, 0.031

10, Sound penetration loss: Db/1000Hz, 22

11, Impermeability: Kgf/㎡, more than 22

12, Water absorption rate: %, 0.8

13, Wind pressure (negative pressure) : Kgf/㎡, -240 frame 600 pitch

14, Metal carved board bending damage degree: Kgf, 58

15, Pencil hardness value: no abnormality, H above

16. Saline spray: no abnormality, 100HR

17, Corrosion resistance: no abnormality, 72HR.

 

 

Product advantage

External metal faced sandwich panel 16mm is uniform and stable

Good heat insulation performance.

Good waterproof performance

The screw is hidden under the plate to prevent corrosion and ensure the overall beautiful effect

Prefabrication saves construction time and is more economical and convenient than the traditional external wall insulation method

Extended service life

In line with the national advocate of "green construction, green building materials" standard

Notes for metal carved board storage

In many construction decoration metal plate of carve patterns or designs on woodwork is now widely used, because it conforms the concept of green environmental protection There are a variety of product styles for us to choose, and the appearance of the product is very beautiful and durable However, due to the wide characteristics of the products, people do not pay attention to the occurrence of building fire events during storage, which not only affects the normal use but also increases the cost of the products. Therefore, in order to reduce the phenomenon of fire, we need to pay attention to the following matters during storage.

1. Metal faced sandwich wall panel 16mm should be surrounded by non-combustible materials.

2. It shall be a fire-forbidden area, and there shall be no open flame operation within 10m around and above it, and there shall be a marked mark.

3. Inflammable, explosive and other dangerous goods shall not be placed nearby.

4. Should be equipped with metal carved board suitable fire extinguisher, sand box or other fire extinguishing equipment.

5. The storage amount of materials should not exceed the amount required by the project for 3 days, and should be completely covered by non-combustible materials.

 

 

 

Certification

We have a full range of qualifications so our quality can be guaranteed.

 

Product transportation

We usually transport the goods by sea. The domestic port we usually use is Qingdao port.

 

 

FAQ

1.Can we be your agent?
Yes, welcome to cooperation with this. We have big promotion in the market now. For the details please contact with our overseas manager.

2.Would you have a discount if l have a large order of metal pu foam sandwich panel?
Yes we could offer different discount according to your order quantity.

3.Do you accept custom design on size?
Yes, if the size is reasonable

4.Could you print our company LOGO on the nameplate and package?
Yes, we can do that

5.Can you give me a discount?
Discount is available,but we have to see the real quantity,we have different price based on different quantity,how much discounts is determined by the quantity.

6.What is your metal faced sandwich panel 16mm’s advantage compared with your competitors?

(1). Qualified Manufacturer

(2). Reliable Quality Control

(3). Competitive Price

(4). High Efficiency working (24*7hours)

(5). One-Stop Service

 

 

Hot Tags: exterior wall siding sandwich panel, China exterior wall siding sandwich panel manufactures, suppliers, factory, steel sandwich panel, aerocon panel house construction, Insulated Metal Sandwich Wall Panels, wall panel sandwich, carbon fiber sandwich panel, sandwich panel warehouse